Firmware Upgrades
From October 2020 any updates of the divecomputer.eu will be made only at the factory service. If you have divecomputer.eu device dated before NXP version and the device is in 2 years free upgrades period please contact service at help.divecomputer.eu
History of firmware updates
Below you can find history of changes in firmware versions of divecomputer.eu device.
Final version 2020 - NXP
- Removed all reported bugs
- Implemented the latest chip compass with tilt compensation
- Hardware improvements to enhance the stability of software
Important! This version of the firmware is dedicated to the latest mainboard hardware signed as NXP version. This version closes future development of the divecomputer.eu device. After long test we can’t find any software bugs and also hardware is simplified to the maximum. Previous versions of divecomputer.eu can be upgraded to this mainboard with NXP software only in the factory.
Version 4.1 & 5.1 - December 2019
- Improved stability
- Removed all minor reported bugs
Version 4.0
- Improved stability
- Removed all minor reported bugs
- hardware improvements to enhance the stability of software
Important! Firmware 4.0 works only with Hardware 3.0. Upgrade needs to be done in the factory as it requires replacing the main board. If your divecomputer.eu has software 3.3 or below, please contact us through the ticketing system at help.divecomputer.eu. If your divecomputer.eu is already Firmware / Software 4.0 Hardware 3.0, there is no need for any updates.
Version 3.3
- Fully implemented support of libdivecomputer.org allowing to transfer logs to the latest versions of “Diving Log”, “Subsurface”, “MacDive” or other softwares using libdivecomputer.org (special thanks for Jef Driesen for his excelent work)
- Solved problem of occasionally showed “OVR” communicate at CCR Fixed Setpoint mode
- Improved calculations of TTS in CCR Fixed Setpoint mode
IMPORTANT! This firmware version is designed for the device version 2018 equipped with wet contacts and bootloader version: 3.0
Cumulative update
Main software version: 3.2C
Bootloader version: 3.0
- Eliminated all critical exceptions involved with FRAM memory communication.
- Implemented software I2C BUS supervision
- New self diagnostic during the start, checking:
- depth (pressure) sensor
- compass accelerometer
- FRAM memory
- Added new mode – “Pure Bühlmann”
- Added variable min and max PPO2
- Added display of current PPO2
- Added full support of libdivecomputer.org allowing for data transmition from Divecomputer.eu to any divelog software with use this library.
- Improved “MacDive” electronic logbook support.
- Solved issues involved with many lines in logbook diagrams
- Improved battery working time.
Please read manual describing how to do cumulative update
IMPORTANT! This firmware version is designed for the device version 2018 equipped with wet contacts. If you have the device without wet contacts with firmware 2.x do not install this version, it is not backward compatible. To get free hardware upgrade from version 2017 to version 2018 of your dive computer please create a ticket on our support portal at help.divecomputer.eu
Version 3.1
- Changed the start of dive logging from the depth of 100cm
- Changed depth of transition to underwater mode at 100cm
- Depth measurement when:
- pressure > ATM + 100mBar
- WetContact
- UW_Permanent_Mode active
- Extended period of atmospheric pressure averaging (50 samples)
- Deletion of pressure sensor calibration values during “Restore to defaults”
IMPORTANT! This firmware version is designed for the device version 2018 equipped with wet contacts. If you have the device without wet contacts with firmware 2.x do not install this version, it is not backward compatible. To get free hardware upgrade from version 2017 to version 2018 of your dive computer please create a ticket on our support portal at help.divecomputer.eu
Version 3.0
- Added wet contact support, installed in devices in version 2018
IMPORTANT! This firmware version is designed for the device version 2018 equipped with wet contacts. If you have the device without wet contacts with firmware 2.x do not install this version, it is not backward compatible. To get free hardware upgrade from version 2017 to version 2018 of your dive computer please create a ticket on our support portal at help.divecomputer.eu
Version 2.2
- Added indicator of ascent speed (OC REC, OC TECH, CCR)
Version 2.1
- Added battery type selection screen.
- Improved linearity of battery discharge indication in percentages.
Version 2.0
- Improved options at Extended Gauge section
Version 1.9
- Firmware includes fixes of all recently found issues.
- Added feature shows TTS in two ways.
Version 1.1
Initial version
- initial beta prerelease APNEA
- initial beta prerelease EXT GAUGE
- initial beta prerelease OC REC
- initial beta prerelease OC TRIMIX
- initial beta prerelease CCR FIXED SP
- Bootloader for Bluetooth module V1